Engineering Extremes: Why Mexico City Takes the Air Out of a Formula 1 Car

Kimi Antonelli became Formula 1's youngest-ever world champion in Mexico City, sealing the title at the age of 20 with third place, while Max Verstappen won a red-flagged race from fifth on the grid, less than a second ahead of polesitter Lewis Hamilton.

But behind a historic result sits a circuit where the biggest engineering challenge isn't a corner, a kerb or a straight. It's the air itself.

The Autódromo Hermanos Rodríguez sits around 2,240 metres above sea level, the highest circuit on the calendar by a wide margin. At that altitude, the air is roughly a fifth less dense than at a sea-level venue. Almost every system on a Formula 1 car depends on air in some way, whether to create downforce, to cool components or to feed the engine. Take a fifth of it away and every one of those systems behaves differently. For teams, and for the supply chains behind them, that creates a very particular set of demands.

Maximum Wing, Less Downforce

With less air flowing over the car, the wings and floor generate less downforce at any given speed.

Teams respond by running their highest downforce configurations of the season, comparable to Monaco, yet the car still ends up with less grip than it would have at sea level. There is one upside. Thinner air also means less drag, so even with maximum wing, the cars reach well over 340km/h at the end of a main straight more than 1.2km long. The result is a car that is fast in a straight line but short of grip everywhere else, a combination that makes braking and slow-corner traction especially difficult.

The Cooling Problem

Every cooling system on the car relies on air passing through it, and in Mexico City there is simply less of it to do the work.

Radiators, power unit cooling and brake ducts all lose effectiveness, so teams arrive with larger cooling openings, accepting the aerodynamic penalty to keep components within their limits. The problem grows in traffic. A car following closely receives disturbed, hotter air, and temperatures can climb quickly, which often limits how long a driver can sit behind a rival before having to back off. It's a reminder that the materials inside a Formula 1 car need to hold their properties when the margin for cooling has been taken away, not just under ideal conditions.

A Harder Job for the Power Unit

Altitude has always been a test for turbocharged engines. With lower air pressure at the intake, the turbocharger has to work harder to deliver the air the engine needs. Under the 2026 rules that challenge has grown. The MGU-H, which previously helped control the turbocharger electrically, has been removed, so the turbo now has to manage on its own.

Working harder raises the temperature of the compressed air, which places more load on the intercooler, which in turn is working in thin air with reduced cooling capacity. At the same time, cars were expected to run at or near maximum electrical deployment, and on a lap with only seven braking zones there are limited opportunities to recover that energy.

Braking in Thin Air

The braking zone at Turn 1 is one of the most severe of the season, with cars slowing from around 340km/h to little more than 110km/h in under 200 metres. In thin air, the heat generated in that stop is harder to shed. Carbon discs can approach 1,000°C, and with reduced cooling airflow, managing brake temperatures becomes one of the defining challenges of the weekend.

Lower downforce makes braking harder still, and this year's cars carry less of it than their predecessors. The braking zone for Turn 4 is more than 40 metres longer than it was in 2025, keeping the brakes working for longer on every lap.

A New Surface

This year added another unknown. Most of the circuit was resurfaced ahead of the race, replacing the bulk of the original asphalt with a new surface. New asphalt changes grip levels, tyre wear and temperature behaviour, and the darker surface can produce larger temperature swings between sessions. With Pirelli bringing its three softest compounds, teams had to relearn how the tyres would behave at a venue where they thought they already had good data.

What Makes Mexico City Unique on the F1 Schedule, and How Do Engineers Overcome It?

No other circuit on the calendar combines these pressures in quite the same way.

Its altitude reduces downforce, so teams run maximum wing and still end up with less grip than they would at sea level. The same thin air reduces cooling, so radiators, power unit systems and brakes all have less margin, particularly in traffic. The power unit's turbocharger has to work harder without electrical assistance, adding heat to a system that is already struggling to shed it. And with heavy braking, limited energy recovery and a largely new surface, almost every reference point teams brought from previous years had to be rechecked.

Engineers and Designers Don't Overcome This With a Single Fix

They respond across the whole car: maximum downforce packages to recover grip, enlarged cooling openings for the power unit and brakes, power unit calibrations tailored to thin air, and energy strategies built around a small number of braking zones. Every one of those responses depends on components and materials that hold their properties at high temperature, with reduced cooling margin and under heavy, repeated braking loads, which is precisely the environment our customers were engineering for in Mexico City.

Smiths High Performance is a Tier 1 supply chain partner to the global motorsport industry, supplying high-performance alloys and engineering plastics to Formula 1, MotoGP, WEC, NASCAR and WRC.

Get in touch with Smiths High Performance to discuss your team's material and supply requirements.

Contact us at info@smithshp.com or call +44 (0)1767 604 708.

Supply Partners

We provide comprehensive engineering raw material support for global motorsport, including Formula 1 teams and their sub-contractors.

DISCOVER