Engineering Extremes: Why COTA Asks for Several Cars in One
Kimi Antonelli moved within touching distance of the world championship in Austin, converting pole position into his ninth win of the season, 13 seconds clear of Charles Leclerc, with Max Verstappen third.
The Mercedes driver made a single pit stop while most of his rivals stopped twice, a strategy that depended on a car able to look after its tyres over a long first stint.
But behind the result sits a circuit that asks more different things of a car in a single lap than almost anywhere else on the calendar.
The Circuit of the Americas runs for 5.5km and 20 corners, and it was designed to borrow from some of the sport's best-known venues: a steep climb to the first corner, a sequence of high-speed esses, a long back straight and a slow, tightly packed stadium section to finish the lap. Every one of those sections pulls the car's setup in a different direction. For teams, and for the supply chains behind them, that creates a very particular set of demands.
One Lap, Several Circuits
Most circuits have a clear character. A team arrives knowing whether the priority is downforce, straight-line speed, braking or traction.
COTA doesn't offer that clarity.
The fast sweeping corners of the first sector reward high downforce and a stable aerodynamic platform. The long run down the back straight rewards low drag. The final sector, with its slow, tight corners, rewards mechanical grip and traction. A setup tuned for any one of those sections gives time away in the others, so every decision becomes a compromise, and the right balance can shift with the wind and the track temperature.
The Bumps
COTA has long been one of the bumpiest circuits on the calendar, and the cause lies beneath the track rather than on it. Ground movement under the circuit gradually distorts the surface, so bumps that are ground out one year can reappear the next.
The circuit resurfaced the section from Turn 9 to Turn 11 and smoothed the approaches to Turns 12 and 19 ahead of this year's race. Even so, the first sector remained rough, and a dip on the entry to Turn 1 only came to light in race week, too late to be fixed.
For a modern Formula 1 car, bumps are more than a comfort issue. The floor generates its downforce most effectively when it runs close to the ground, so every bump forces teams to choose between running low for performance and running high enough to protect the floor and keep the car stable. Each impact also travels through the suspension, the floor and the structure around it, lap after lap, for an entire race distance. It's a reminder that the materials inside a Formula 1 car need to withstand repeated impact and fatigue loading, not just steady peak loads.
Uphill Into Turn 1
The climb to Turn 1 is one of the most recognisable features on the calendar. Cars brake hard up a steep gradient into a tight left-hander, then crest the hill and drop away towards the esses. Braking uphill helps slow the car, but the crest unloads it at the exact moment the driver needs grip, and the dip at the entry this year made the braking zone harder still. The same corner is also the main overtaking point at the end of the start-finish straight, so it has to work in traffic as well as on a clean lap.
Energy Through the Esses
The fast sequence from Turn 3 to Turn 8 is closer to Suzuka than to a typical modern circuit, and under the 2026 rules it brings its own energy problem. The esses are sensitive to wind and throttle input, and a car that spends too much electrical energy through the first sector arrives at the long back straight with less to deploy. With two active aero zones, on the approaches to Turn 1 and Turn 12, teams have to plan where energy is recovered and spent across the whole lap rather than corner by corner.
Tyres Under Every Kind of Load
Because the lap contains so many different types of corner, the tyres are loaded in several different ways. The rears are the first to suffer, overheating under traction out of the slow corners of the final sector, while the front left takes sustained load through the long multi-apex right-handers late in the lap. Late October in Texas adds another variable. Conditions can range from cool to very hot across a weekend, and track temperature falls as the sun sets during qualifying.
Managing Component Life
Coming late in the season, Austin also tests how well teams have managed the life of their components. Several cars started from the back of the grid after exceeding their power unit allocations, a reminder that durability over a full season matters as much as performance at any single race.
What Makes COTA Unique on the F1 Schedule?
No other circuit on the calendar combines these pressures in quite the same way.
COTA packs high-speed esses, a long straight and a slow stadium section into a single lap, so no single setup suits all of it. Its bumpy surface, caused by movement in the ground beneath it, forces a compromise between ride height, floor performance and stability. Its steep climb into Turn 1 creates a braking zone that unloads the car just as grip is needed most. And its variety of corners loads the tyres in several different ways, in weather that can change sharply across a single weekend.
Engineers and Designers Don't Overcome This With a Single Fix
They respond across the whole car: suspension and ride height settings that absorb the bumps without giving away too much floor performance, aerodynamic packages that balance downforce in the esses against drag on the back straight, energy strategies planned across the whole lap, and setup work to protect the rear tyres in the final sector. Every one of those responses depends on components and materials that hold their properties under repeated impact, sustained fatigue loading and rapidly changing conditions, which is precisely the environment our customers were engineering for in Austin.
Smiths High Performance is a Tier 1 supply chain partner to the global motorsport industry, supplying high-performance alloys and engineering plastics to Formula 1, MotoGP, WEC, NASCAR and WRC.
Get in touch with Smiths High Performance to discuss your team's material and supply requirements.
Contact us at info@smithshp.com or call +44 (0)1767 604 708.
