Engineering Extremes: How Do You Prepare for a Race That Wasn't on the Calendar?
Formula 1's unexpected return to Sepang produced a rain-delayed race and Max Verstappen's first win of the season, the Red Bull driver finishing 2.3 seconds clear of championship leader Kimi Antonelli, with Lewis Hamilton recovering to third.
It was a fitting result. Verstappen also won the last Grand Prix held here, back in 2017.
But behind the result sits a question that almost never comes up in modern Formula 1: how do you engineer a car for a race that wasn't in the plan when the car was designed?
Sepang only joined the 2026 schedule in late July, when it was confirmed as host of the relocated Bahrain Grand Prix. That left teams around ten weeks to prepare for a 5.5km, 15-corner circuit that Formula 1 hadn't visited for nine years, in some of the hottest and most humid conditions of the season. For teams, and for the supply chains behind them, that combination created a very particular set of demands.
A Formula 1 season is planned around its calendar long before the first race. Cooling layouts, upgrade schedules, spares allocation and freight are all mapped against a known sequence of circuits. Adding a race partway through the year disturbs every one of those plans.
The event teams had originally planned for was a spring race in the desert, run in the cool of the evening. What replaced it was an afternoon race in the tropics in October, slotted between Baku and Singapore as the middle leg of a triple-header. That meant circuit-specific parts, particularly for cooling and braking, had to be designed, manufactured and shipped on a much shorter timeline than usual, and within the limits of the cost cap. It's a reminder that performance depends on lead time as well as design, and that having the right materials available at short notice can decide whether a part reaches the car at all.
What Do You Do When the Data Is Nine Years Old?
Sepang was a familiar venue until 2017, but almost nothing from that era carries over.
Since then the cars have been through two complete regulation changes. Wheels have grown from 13 to 18 inches, the power units now draw close to half of their output from electrical energy, and active aerodynamics has replaced DRS. Only a handful of the current drivers have raced a Formula 1 car here, and that experience offers little guidance on how a 2026 car should be set up.
So teams started from simulation. Lap models were built around the circuit's geometry, then fed with loads measured this year at tracks with comparable corners, giving a first estimate of temperatures, tyre energy and component duty. Friday practice then became a correlation exercise, checking how closely the real car matched the predicted one and adjusting quickly where it didn't. When the load case is a prediction, parts are designed with more margin, and the materials inside the car have to behave predictably across that wider window.
The Heat and Humidity Problem
Sepang's climate is its defining feature. Ambient temperatures sit in the low 30s, humidity regularly exceeds 80% and track temperatures can approach 60°C in the dry.
High ambient temperature narrows the difference between the air entering the radiators and the fluids they are trying to cool, so every cooling system on the car becomes less effective at exactly the point it is needed most. That affects more than the engine. The 2026 cars carry far larger electrical systems, and the battery and power electronics have tight temperature limits of their own. Opening up the bodywork recovers cooling, but it costs aerodynamic efficiency on a circuit with two straights of close to a kilometre each.
Three Straights and One Battery
The back straight, the pit straight and the run to Turn 4 come almost one after another, separated only by the final hairpin and the opening corners. Under the 2026 rules, that concentrates electrical deployment into one part of the lap and leaves the flowing middle sector as the place to recover energy.
The heavy stops into Turn 1 and the final hairpin, from well over 300km/h, do much of that recovery work, and the car has to harvest hard through the rear axle without unsettling itself under braking. It also means braking and energy recovery systems see large, repeated thermal swings, in air that does little to help them cool.
A Surface That Punishes Tyres
Sepang's asphalt is abrasive, and its long, fast corners put sustained energy through the tyres. The front left takes heavy lateral load through the Turn 5 and 6 sweep, while the rears are prone to overheating on traction out of the slower corners. Managing that on a hot track is as much a mechanical question as a tyre one, shaped by suspension geometry, weight distribution and how the car delivers its torque.
When the Rain Arrives
Then there is the weather. Heavy rain delayed Sunday's start, and the field split between intermediate and slick tyres when the race finally got under way. With very little wet running behind the 2026 cars, teams had few reference points for how they would behave, on a track that can go from soaked to dry in a matter of laps. Components that have spent a weekend running hot are suddenly working in standing water, one more rapid change in temperature for the car to absorb.
What Makes Sepang Unique on the F1 Schedule, and How Do Engineers Overcome It?
No other race this season has combined these pressures in quite the same way.
Sepang arrived at around ten weeks' notice, compressing design, manufacture and logistics for a race nobody had planned for. It hadn't hosted Formula 1 since 2017, so every load case and temperature target began as a simulation. Its heat and humidity reduce the effectiveness of every cooling system, on a car that now has more to keep cool than ever. Its layout concentrates energy deployment and heavy braking into one part of the lap, while its abrasive surface and long corners work the tyres hard everywhere else. And its weather can rewrite the conditions completely within minutes.
Engineers and Designers Don't Overcome This With a Single Fix
They respond across the whole car: expanded cooling for the power unit, battery and brakes, energy strategies built around the three straights, setup work to protect the rear tyres, and simulation models that are corrected against real running as soon as the cars reach the track. Every one of those responses depends on components and materials that hold their properties under sustained heat, repeated thermal cycling and conditions that couldn't be fully measured in advance, and on a supply chain able to deliver them quickly, which is precisely the environment our customers were engineering for at Sepang.
Smiths HP is a Tier 1 supply chain partner to the global motorsport industry, supplying high-performance alloys and engineering plastics to Formula 1, MotoGP, WEC, NASCAR and WRC.
Get in touch with Smiths High Performance to discuss your team's material and supply requirements.
Contact us at info@smithshp.com or call +44 (0)1767 604 708.
